Skip to content
KRASNO LABS

Independent engineering studio

From concept to functional hardware.

Krasno Labs designs and builds precision mechanical hardware — 3D CAD, functional additive manufacturing, mechatronics and light automation. Engineered around real loads, real tolerances and real deployment conditions.

  • DFAM-first
  • ESP32 / PLC
  • CAD → part
  • EN / ES
DWG_KL-0142 Mounting flange · PA-CF
Ø 64 Ø 20 H7 0.10 A 6× M4-6H Ø 50 BCD 12 A DWG KL-0142 NTS REV C A3

Material

PA-CF

Layer

0.12 mm

Tol

±0.15 mm

Typical XY tolerance
±0.15 mm Typical XY tolerance
Prototype lead time
5–15 days Prototype lead time
Industrial + advanced manufacturing
2× M.Sc. Industrial + advanced manufacturing

Core services

Engineering services built around the build.

Three focused disciplines, one accountable engineer. Scope is fixed before material is committed, and every deliverable is something you can hold, measure and run.

03 / disciplines

SVC_01

3D CAD & Functional Additive Manufacturing

Design for Additive Manufacturing (DFAM), custom enclosures, jigs and fixtures, plus end-use parts in engineering polymers — modelled around loads, assembly and print orientation.

  • DFAM review and print-oriented geometry
  • Custom enclosures, brackets, jigs and fixtures
  • End-use parts in PLA, PETG, ABS, PC, TPU, nylon and CF / FG blends

CAD → MESH → PART

SVC_02

Mechatronics & System Integration

Sensor and actuator integration, custom test rigs, and microcontroller or PLC prototyping — from an ESP32 proof-of-concept to industrial I/O wired to a live process.

  • Sensor and actuator integration and wiring
  • Custom test rigs and data acquisition
  • Microcontroller and PLC prototyping (ESP32, Arduino, industrial I/O)

SENSE → ACT → CONTROL

SVC_03

Technical Consulting & Light Automation

Hardware troubleshooting, proof-of-concept builds and Python/C++ control scripting — tightly scoped for teams that need a working prototype, not a slide deck.

  • Hardware fault-finding and design review
  • Proof-of-concept builds and bench validation
  • Python / C++ control scripting and tooling

DIAGNOSE → SCRIPT → AUTOMATE

Technical capabilities

The bench, in numbers.

Hallmarks of the current lab setup. Values are indicative and confirmed per project during scoping.

Build volume SPEC_01

250 × 250 × 300 mm

Materials SPEC_02

PLA · ABS · PETG · PC · TPU · Nylon · CF / FG reinforced

Dimensional tolerance SPEC_03

±0.15 mm typical · ±0.05 mm critical fits

Layer resolution SPEC_04

0.08 – 0.28 mm

CAD & control stack SPEC_05

Fusion 360 · SolidWorks · ESP32 · Python

Typical lead time SPEC_06

5 – 15 working days

Units in mm · values confirmed per project

Selected work

Lab builds, documented end to end.

Representative builds from the bench. Client names withheld — full case files available under NDA.

ENCLOSURE / DFAM

Sealed sensor enclosure for a washdown line

Problem
Off-the-shelf IP-rated boxes forced a bulky layout and a cable route that failed inspection.
Engineering solution
Single-piece PA-CF housing with an integrated gasket channel, angled gland ports and a print-in-place hinge.
Outcome
38% smaller envelope, repeatable seal at 0.5 bar, 11 days from sketch to fitted part.

TEST RIG / MECHATRONICS

Endurance rig for a linear actuator

Problem
Manual cycling topped out at 40 cycles per hour with no repeatable force data.
Engineering solution
ESP32 controller, load cell and a Python acquisition loop logging force, current and position every cycle.
Outcome
1,200 cycles per hour unattended, 24-hour runs, force and current curves captured for every unit.

CELL / LIGHT AUTOMATION

Sensor-gated counting cell for small batches

Problem
Manual counting and bin handling made throughput operator-dependent and error-prone.
Engineering solution
Retrofit conveyor gate with photoelectric sensing, custom fixtures and a Python HMI on a panel PC.
Outcome
3× throughput on the same bench, scrap under 1%, no PLC licence required.

Files: CAD source, print logs, test notes

Project intake

Tell us what needs to exist.

Send the brief — geometry, constraints, deadline. You get a scoped reply with approach, milestones and price range, normally within two working days.

Prefer email?

[email protected]

Send drawings or a rough sketch to the studio inbox. Attachments up to 25 MB are fine, including .STEP and .STL.

Write to the studio

Independent studio · NDA on request · EN / ES

INTAKE_FORM.v1

KL / EN-ES

CAD files (.STEP / .STL)

Attach .STEP or .STL

Max 25 MB per file · optional at first contact

Upload is handled after submission: reply to the confirmation email with your files, or send them directly to [email protected].

Typical reply within 2 working days · EN / ES

Your brief stays confidential. No mailing list, no resale of data.